NGX 5pc Deluxe Clamp Edge Set - 50 inch Guide Rail + 50 inch Rail Extension, NGX Saw Plate, T-Square Attachment & Track Clamps - Track Saw system for Circular Saw - 544550

I purchased this saw track to cut T-11 panels into planks to use on a ceiling. The tool was easy to set up using the included instructions. The tracks are solid and I expect to have them for a long time. I cut ten sheets into six planks each with no problems. Each cut was straight.The saw track is a stiff plastic and glided down the track with no problem. My only issue is the clamp are plastic and I'm concerned they will break if over used. The plastic feet on the screws you tighten to hold the saw on wore off after tightening. They still held the saw in place.I highly recommend this tool. The clamps hold tight and it was easy to move from cut to cut. I'm sure I will find many uses besides just a track saw. It makes a solid and true straight edge.I'll never need to use my table saw again for large sheets of wood.

As described and works very well for what it was made for. Customer service was helpful as one of the parts for tee squre was stripped, they are sending me a new part.

The most important after you receive your product is to be "patient doing the initial set up". I am doing a woodworking bench 2'x7'x37", I get the plywood for the top and bottom shelfs cut at the big store, but the cuts where not exactly 2', the actual size of a full plywood is actually 4'-1/2" and they cut it in half with a very bad blade, the cut was horrible, my shop is small and I can not handle big pieces of plywood to trim it to the correct size. This is why I decide to buy the BORA 5 piece NGX set, I have a Skill 7 1/4" blade circular saw that is very, very old and it was not giving me very strait cuts, first I get and install a new 40 teeth carbide blade and clean and adjust the saw, put the saw on the new BORA plastic base, very strong plastic and adjusted to cut with 1/2" offset, I did not like the blade to cut to close to the aluminum track, I already ruin another track doing that, when I tried to connect the other 50" track together then I find out that the first 50" track did not have holes to connect the two metal bars that insert at the end of the track, I was kind of sad with this setback and I decide to drill the holes myself, I did not want to return my track that I was so exited to use, big problem when you do not have the correct tools to do it, the holes need to be drilled on the bottom of a 1/4"x1/4" dado in the aluminum track, finally I did it not perfect but they work, I install the second section and they did not align strait, I have to use a strait set up rule to align the two sections and tight the four screws, finally I set the saw on top of the track check my safety list, the end clamp that slide under the track (it works very good supporting the end of the 8' plywood) and went for the cut, I have the most beautiful strait cut that I ever did with my very old Skill saw, almost similar in quality as done in my table saw, I cut the other three sides and every corner was exactly 90 degree.I am very happy with the product, I will give a 5 start rating if not for the four holes that I have to drill on my brand new aluminum track. Perfect for cutting 3/4" Plywood, I will recommend these product to a friend.

I needed a circular saw guide that would be long enough to cut a door. The instructions that were included were awful - no words and even the pictures were very unclear. After a quick google / YouTube search, we were able to get the instructions we needed. I saw some reviews that said the extension didn’t work well, but we did not have issues when we secured them together with the four screws. It secured easily to the saw and was easy to use. Definitely recommend.

So I just got this and still haven't really used it but some glaring things made me want to get something up. Understand that some things may be user error or a part not assembled correctly but since their directions are purely pictographs with no words and very little guidance it's not my fault... maybe directions or a set up guide with actual instructions would be helpful...The rail seems okay and pretty self explanatory, haven't gotten my precision straight edge out but it's pretty good with something I know is pretty straight. The sled has a little slop, not enough to be an issue for most but will stick a strip of some .02" uhmw in there and it'll be good. The saw mounting just doesn't seem to want to stay perfectly seated and the saw doesn't rest against and positive stops to hold it or to ease putting the saw in and out since I'm not currently dedicating a saw to this, am considering buying the other saw sled they have as it looks better.One other big disappointment was that they give you enough of the anti-chip strip for one 50 inch section of rail but not the two included in this set. That's just cheap. I guess I can put it all on one side and try to always cut on that side of both rails but know there will be a time where I need to flip around. I mean what was another 100 inches of plastic strip going to cost...