BTF-LIGHTING RB3 2.4G Wireless Touch RF Remote for SPI Chasing RGB RGBW LED Strip Light 4 Zone Control Match with SP530E SP630E SP633E SP634E SP638E SP639E SP63BE

Great module. Plenty of different modes to choose from when using the app and yes the app actually does what it's supposed to do ! This module will also power up on the setting you last used before removing power. This module can control just about every led light strip out there. You supply the voltage to the module, 5v,12v, or 24 volt as required by the led strip. Find the led strip wiring type that you have, easy to decipher with the information that comes with the module , connect the wiring and enjoy. I was surprised at how many different led strips that this would control. I used this to control 60 feet of IC sequential led strips and it works great . It is able to light up the leds very brightly too ,which is something the controller that came with the led strips didn't do.

Tested out this controller on my desk with some left over assignable LED lights i had from my TV backlight upgrade. Worked so well and looked so good that my Son ordered a few roles of lights and this controller. Wrapped his whole 10x12 room in them...1 controller was plenty to power the whole run of roughly 200 LED's. Looks like it handles about 30 LED's before the patter repeats. Will be buying more of these for other areas of the house. Remote is a little weak, but the app lets you have nearly full control and great customization of the lighting.

I have been using these for a while work amazing. When I buy LEDs I connect them to these controllers. Using the app is super easy and fast. You can use via wifi or bluetooth to control them. I got the remote just in case but honestly dont use it. the app is great and you can group them and set timers. The remote control is easy to use so this setup is great value for the money. The controller give you many brightness and setting options to use.

The app isn't great but its functional. It crashes frequently on Android. Operation is somewhat intuitive but the installation instructions are terrible and 30 minutes of trial and error will be your friend. As a novice in using LED tape lighting, a better instruction book/pdf would have been nice. Also during installation, the PLASTIC CONNECTORS between LED lights and wires MATTER and will consume 90% of your installation time if you don't know how they work or if you get the wrong item. I listed the connectors liked below. My 'hopefully' helpful hints for what they were worth: This SP630E unit adds Bluetooth and remote control functionality to the WS2812B LED Strips. It is also the interface that transfers power from the transformer to the LED Tape and generates the signals that the LED tape needs to work. This box works well, it is small and can be discretely hidden, but instructions are poor. You can program light sequencing, colors, timers and response to sound with the app. A dedicated remote control is available in different kits or might be sold separately, but you don't need the remote if you plan to control these lights from your phone. The remote is simple and has preset controls for most of what you can do with the lights, but the app (free) allows a little more functionality and control. To use the app, you first have to Bluetooth pair it with the SP630E controller. I had a lot of missteps doing my ordering and first installation of LED lights. My installation was a 6 self, 8 foot high bookcase that I wired as one continuous length but with 5, 12" vertical wire jumps and 48" horizontal LED runs. I was able to hide all the vertical wires fairly well. I goofed up and had to splice a few of the horizontal LED strips but those spices were easy using these flat connectors: Some additional flubs that hopefully you wont repeat: 1. Get a 5V transformer (DO NOT use12V) to power the WS2812B strips 2. Its not complicated. The WS2812B LED strips require only 3 wires for full functionality: --Use a red wire to connect the voltage tab (+5V) on LED strip with the "VCC" port/terminal on the SP630E unit --Use a green wire to connect the middle metal tab (DIN) on the LED strip with the "WC" port/terminal on the SP630E --Use a white wire to connect the ground metal tab (GND) on the LED strip with the "GND" port/terminal on the SP630E 3. The WS2812 LED strips are fairly dense (maybe 2" apart and can show every color and groups of LEDs can be programmed somewhat independently 4. Always pay attention to the arrows when you combine LED strip pieces. The arrows should always be pointing AWAY from the SP630E. If you connect part of the LED strip pieces the the wrong way, the entire strip will not work. 5. Cut straight across the middle of the LED strip metal tabs (where all the arrows are located) between the lights. Connecting a LED strip directly to another LED strip was easy...using https://www.amazon.com/dp/B01NASHQPO?ref=ppx_yo2ov_dt_b_fed_asin_title Just make sure you place the strips tabs under the connector tabs. The 90% elbows in the kit were kind of crappy and tended to be too floppy to reliably connect...probably just me, but the straight connectors were fine, the elbows were a waste. 6. If you want to connect a 3 conductor wire the LED sections (to jump a distance without lights), the ONLY connectors that worked for me was https://www.amazon.com/dp/B09PR418WZ?ref=ppx_yo2ov_dt_b_fed_asin_title I wasted a ton of time trying other ways to connect them. These connectors specifically have 3 small holes on one side to stick the wires in. On the opposite side you stick the metal tab end of your LED strip in, FACE DOWN. The LED metal tabs must face down in the connectors. Be careful that GND connects to GND, +5V connects to +5V and DIN connects to DIN across these connectors. You must click down hard on each side to make an electrical contact take place inside the connectors. The LED tape connection side is a bit tricky to line up, but look thru the clear plastic to ensure that the metal tabs line up inside the connectors. Unfortunately, once you snap either side of these connectors shut, its almost impossible to open them back up if they don't make good contact with the metal embedded inside the connectors. If this is your first time working with these lights, you will waste some connectors. You will wind up cutting LED lights off when you mess up the positioning within the connectors. I got better & faster with every section that I did. Ultimately, you can absolutely do these projects but there is a learning curve.

This unit was easy to connect to the recommended BTF WS2811 RBG strips that was part of the purchase , Downoading the app and connecting to the unit was was also easy. Flipping though the various pre-programed lighting modes was simple and made for some impressive visuals.... that is until it because evident that the LEDs were ONLY rendering in Red, Blue, and Green. The only time other colors like yellow, orange, purple, cyan, white, etc. would show is if the particular mode only lit a small portion of the strand (like the Dot Spin mode). Trying to manually select a solid color for any of the 16 million colors supported by the strands was pretty much impossible, or at least extremely limited and finicky at best. There was a firmware updated suggested upon loading the app the first time and I suspect that it has a fundamental flaw. Will be returning.

works perfect and always reconnects on 1st try

Its surprising how hard this was to find..i was looking for a way to control my pc's lights without a button so this was perfect. I like the remote option but i also want something i could control from my phone so this again was perfect. It was super easy to set up and they give you the option to connect to a simple 5v light or a 12v both with different power inputs. Color rage is amazing and has every color you light can support. I also like how compact it is and that they include the screwdriver as it's pretty small and i dont think the average household would just have that size on hand. Overall such a simple idea thats so hard to find for some reason and it comes at a reasonable price. Definitely a specific product for a specific need but this is your best option for it.

Works great both the controller and the bluetooth function come in handy whenever changing any color or pattern for my LED strip and is easy to use