3D Printer Enclosure with LED Light,Dustproof Tent Constant Temperature Protective Cover for Creality Ender 3 V3 SE/KE/Ender 3/Ender 3 Pro/Ender 3V2/Ender 3S1/Neo/Anycubic Elegoo, Medium

Easy to put together, seems to stop draughts and retain heat quite well. The opening is big enough to lift an ender 3 in and out with little issue. Could possibly do with not being as deep but my guess it is as such to accommodate different size printers. It's withheld a few months work without issue. I got the enclosure with the LED light and this is surprisingly lights quite bright. Probably helped by the fire retardant coating on the inside of the enclosure. Oh and it is incredibly lightweight.

This has to be the best upgrade you can make for any open frame 3d printer. The quality is way better than I expected. Abs prints are coming out flawless, even with the fan on up to 40%. It took 5 mins to assemble this and the medium size is a perfect fit for for my neptune 4. If I was to try and find a fault it would be that the zip only opens from the outside so if your wife convinces you to get in it you can't escape until she let's you out.

Excellent enclosure for my Ender 3 sat in the garage. Winter temp around 6-7deg C - printing temp around 20-25 deg inside enclosure. The LED light works well and the material and zip feel and looks quality. I would recommend putting it together on a bench or table or wooden floor, as the cover is a snug fit on the frame. Use gloves and protect any worksurface when putting it together as the connecting rods leave a black residue behind.

There are larger and cheaper variants from better known brands in 3D Printing; however, this beats them for me because of the number and size of openings it has. Two rubber gromets at the rear for power or other cables, a large left side access port with a Velcro-style seal for the cover; and a right rear access port designed for a fan extractor to fit which is also has a flap-cover sealed with Velcro. The light it bright and very suitable for the job and can be fitted to any part of the frame. The only issues I have is that some of the frames poles are loose in some of the connectors so putting it together can be quite fiddly; that being said, once it's constructed the material is tight fitting so it holds it all together well. I'm also pleasantly surprised at the ability to hold the temperature. It's installed in my uninsulated garage and I turned off the internal heater I've added (which was set to 35°C) around 23:00 last night and this morning it was still at 25°C inside the enclosure despite being around 15°C outside and even lower overnight. The fifth star is lost because of the lower quality of the frame (loose fittings) and the higher price than others for it's size and features

Great enclosure for my Kobra 3 snug fit and easy to assemble

The sidewinder just fits comfortably in, any bigger, and there’d be no room for adjusting the bed height etc. I have a sidewinder X1 V4, and this will stop out getting dusty nicely. The lights are good and bright too. It’s big enough to fit the filament holder, but not with a roll of filament on top, so you’ll need to feed the filament in through a gap, but the double zip allows this, and you’ve probably got a dryer anyway if dust if a concern! Easy to assemble, so should be easy to take apart too. Good value cover.

More than big enough for my Kobra 3 and if I had the Ace fitted to the top of the Kobra 3 uprights that would probably fit in as well. Liking the fact it has a light. Disliking the smell. The material this is made out of has a very strong odour especially when it is warm, possibly from the flame retardant used. All in all this is very effective at containing my 3d printer and as it is more than big enough to fit my Ultimaker 2+ extended I am buying a second one for that.

Great enclosure. I fit an Anycubic Mono 4 in there and a wash and cure station. Plenty of room, without being cramped. Can get the lid off easily, due to room. Easy to build, with instructions and worth every penny. I keep in the shed, which seems to hold the temp well. It holds the stinky fumes in there, keeping the smell inside. I’d advise putting some extraction on there too.

I've been meaning to get an enclosure for ages, as my printer sits near an HVAC vent and I know that doesn't help prints. Temps vary wildly in the basement too, and I'm sure that isn't helping. Finally pulled the trigger on this enclosure. The medium size is HUGE and has more than enough room for my Ender3 Pro. Assembly was straightforward, and didn't take too much effort. Directions were good. Just make sure you fully seat all of the rods into their sockets and you shouldn't have any issues. I found it easy to assemble the frame and set it on the floor, then slide the the cover over the frame, versus the directions saying to try to drop the frame into the loose cover. It's a snug fit, but it went on with no problem. I was able to zip-tie my webcam to the frame, so it didn't need to sit on the stand that I printed for it anymore, which is a nice space saver. I need to clean up some wires and make things look nice inside, but it's a great enclosure that should help me get more clean and consistent prints. It also cut the fan and printer noise way down, which is great! My only small complaint would be the light bar - it puts out enough light in there to work, but I feel like no matter where I've tried to move it, it's just not quite right with my webcam and Klipper. I see they sell additional lights, so I may buy one, or just design and print some other kind of solution. Other than that one small thing, which isn't worth knocking the product, as it's a personal preference, this enclosure rocks!

Per quanto costa è un upgrade alla stampante 3d incredibile, non ho più avuto alcun problema di warping e fallimenti di stampa da quando la uso, ho iniziato anche a stampare ASA e abs con un estrattore in garage e ha dato nuova vita a una stampante che non usavo più.

Easy to setup for my Egeloo printer. Supports appeared strong,cover fit very well. No gaps or rough corners. Cables easy to work with through the cover sides. Reflective interior keeps temp stable. LED light works well. A good purchase!

Lo recomiendo al 100/100 muy buena calidad y se monta muy rápido mi impresora es una bambú lab a1 y entra en el armario perfectamente rine si espacio de sombra lo recuerdo 😊

Quedó muy bien para mi impresora Ender 3 S1 Pro