Fire Pit Pan with Burner

This was my first fire pit build. I had some old deck boards from when I remodeled my deck and put together a concrete top to hold the pan. The Pan was extremely easy to install. Instructions were clear and shows connection options for both LP and NG. I have it temporarily hooked up with propane until I run the natural gas line to the location. As you can see in my video, it has a really stout flame. The 90k BTU provides plenty of warmth and the flame is really consistent across the entire burner. I don’t have any complaints about it. I did get a little discoloration on the edge of the pan where the flame drifted due to the slight breeze we had. Probably because of the propane vs natural gas. However it cleaned off easily. My only recommendation would be to buy a multi-turn valve vs a quarter turn valve. I bought the Stanbroil quarter turn valve and it doesn’t allow much fine-tuning of the flame. It is nearly all or nothing. And the “all” is a huge flame. My video shows about the minimal flame I could achieve the quarter turn value. So if you want a small flame, keep that in mind. On another note. I purchased both the Stanbroil valve and electric ignition that were recommended. Neither come with documentation for install or operation. I had to kind of figure it out. But was not too bad. The pan comes with a plate for installing the electric igniter, but doesn’t say what it is for and does not provide the screw to mount it. Luckily I had some stainless steel hardware on hand. Once installed it worked flawlessly however. I would recommend this product. It is a Good value, easy to install and provides a great flame. I am happy with it so far.

I'm a fabricator and was VERY impressed by the fit, finish and quality of this unit. The dimensions are VERY tight and what is listed. Unlike most products you can't trust what it listed, you can bet your life on these dimensions! Installed easy, looks great and works perfect. Will be buying more soon!

Run the biggest gas line you can and get the biggest gas valve you can for the biggest flame. This is with a 1” line all the way back to the meter and 3/4”gas valve. Neck down to 1/2” inlet at the bottom of the pan.

It's beautiful set in stone and the product is well built. A couple things to consider: 1. Don't buy an igniter that says, bought with this pan. 2 igniters did not connect to the product. The stainbroil igniter attached but was too thin for the rock. 2. If your yard is windy, the flame will go out repeatedly. Our wood pit did not have issues but this gas pit keeps going out, filling the air with gas. It's not that windy today, normally much worse. Consider pit placement. Hopefully our new sofa with canopy shading will break the wind. Good luck.

This was way easier than I thought to build and I saved a lot of money. If you’re handy at all this is a simple but awesome way to upgrade your back yard. Highly recommend

I was a little worried about this when I read how it warps when it gets hot. This is a picture of my Fire Pit after it's been on about 45 minutes at full open. It got me to thinking, I cut my hole in my granite slab at about an 1/8 inch extra all the way around (therefore, 1/4 inch play). I think those people that saw it warp probably made the hole just the right size so it was tight. That gives no ability for the stainless steel to expand. I think the extra play relieves that stress. I was very pleased at the height of the flame (using 1/2 inch tubing from natural gas line all the way to burner). And it puts out a significant amount of heat. I installed this piece of granite over a wood whiskey barrel. I gave the cut out in the barrel about 2 inches spacing on every side. After the 45 minutes, the barrel was not getting warm at all. This ends up being a perfect fire pit for us that is movable, so we can place it where we like as the seasons change. I highly recommend it!

This insert was perfect for this project. We were looking for an outdoor table/ firepit combo piece and couldn’t find what we wanted, so I built one. I did a little bit of research and it turned out perfect. The top is concrete countertops. The opening for the fire pit is 1/8” larger than the insert. It has a flange on the outside so you can go a little larger to cover up the edges of your top. This will help prevent any buckling when it heats up. It is hooked up to a LP tank. I did purchase the air flow valve and that creates about 1 1/2 ft. flames. That’s a little too much for our area as it’s in a screened porch. It also puts off a lot of heat which is nice. It also fits a 40lb bag of glass perfectly. The items for the fire pit were purchased off of amazon. The 40lb. bag of glass was fair in price and came in 1 bag.

Great quality and packaging.

Muy buenos productos, excelente calidad.

Very nice high fire

Well built and throws a lot of heat. The included igniter / thermocouple cover plate matched perfectly with the igniter that I ordered separately. I just had to drill a hole for the t/c probe. Very nice flame with lava rock

I first ordered the 18” round burner to complete a do it yourself natural gas fire pit with round stone base. After having extra stone wall units,I quickly fashioned a base rectangle for a more modern clean look and then ordered the Stan broil 30 x 10“ drop in pan and could not be more pleased with it. Highly recommend this product. It puts out some serious heat. Nelson

Burners discoloured fairly quickly.