Winegard DS2000A Universal 22-inch Mount for Off-Air TV Antennas,Grey

Needed a way to mount our StarLink dish to a wall and get over the edge of our roof for an unobstructed view of the sky and this worked PERFECTLY. Went right into the brick with a few tapcons and it doesn't budge. We did also need the StarLink pole adapter but it's all sturdy. Another reviewer mentioned something about it not being 100% painted? The one I received did not have that problem. Coverage was good so I'm not expecting much rust. Note: As per the depiction, you can, in fact, reverse the pole, as I did, to get around wider overhangs. I'm happy with it.

Good product.

I used this to mount my starlink version 2 dish off the side of my house and it worked pretty well. It's almost perfect. The original dish mount has a key in the bore that registers on the bottom of the cable connector. It makes the cable almost impossible to become disconnected once the dish is mounted. The Winegard doesn't have this provision and I missed it when I was checking the fit. It would have been fairly easy to mount a tab in the bore of the Winegard mount but I just didn't see it. Consequently I had to remove the dish several times and re-seat the connector as it kept falling out. The last time I wrapped the connector and the cable with electrical tape and it is holding fine for now. If I have to revisit the mount I will add a more permanent solution. No fault of Winegards. The mount is well made and is still a great way to mount the dish.

Works fine

Our first mount got lost in UPS and a replacement sent quickly. Very easy to install. The length gave us just enough to avoid Starlink obstruction (glad we went with the longer mount). Nice and sturdy.

Bought this to mount my over the air antenna. Right away i could tell this mount was made with good materials and had a nice hefty weight and feel to it was very pleased. Assembly was pretty straight forward and mounting it too. Had out side for a while and its doing its job can't complain a good buy.

Starlink is my ISP and instead of using their supplied ground base or purchasing one of their mounts, I used this to mount my antenna to an eave on my house where it has an unobstructed view of the sky. The antenna dropped right into the end of the tube without any issues and it stays put. The mount is sturdy and has enough adjustment to get the antenna away from the roof line to allow it to adjust for the best signal.

Worked out great for installing Starlink. Used it along with an antenna adapter with U bolts. Pipe is large enough to route the Starlink cable inside it. It is actually much bigger than I expected. Make sure you have enough room to screw in the base plate if you are mounting it on a beam or joist rather than a wall. I mounted it on a beam and had to do it where a post met the beam to get enough space for all the lag screws to keep the base plate stable.

Very good and strong mount for antennas. I installed my Antenna Direct DB8-E antenna, that you can also buy here on Amazon.ca, on this mount. It is built very strong, I'm very happy with my purchase.

This is the perfect fit for my starlink dish and it does its job very well, especially with the attachment and handles all the weather conditions on a flat top roof, especially wind.

Some have claimed that this mount does not provide a tight fit for a rectangular starlink unit. That is true if what one expects is that the mount provides the same insertion fit and 'button' locking you get from a standard starlink mount. It does not do that. But the internal diameter of the mount is 1.52" and the starlink's shaft's largest diameter (beyond the reduced-diameter starlink-specific mount area) is 1.5". Wrapping some electrician's tape around the 1.5"" diameter area of the starlink unit might be enough to get a tight fit. But better, I think, is using a 1.25" flexible pipe connector (1.25", not 1.5", because the outside diameter of 1.25" internal diameter pipe (metal, ABS, etc.) is approximately 1.5") provides a waterproof and more stable solution. Put the pipe connector on the mount shaft, leaving about an inch of rubber (actually black flexible PVC) for the starlink shaft and push the shaft into the mount about 2", thereby placing about an inch of the 1.5" shaft in the mount. You could even wrap tape around the shaft too. Tighten both clamps. Be sure, of course, to put the starlink cable through the bottom of the mount and insert it in the starlink unit before inserting the unit into the connector that is placed on the mount. I can't guarantee that this solution provides as much stability as a starlink mount; among other things, placing the starlink unit on a 22" shaft rather than locking it into a starlink mount that does not add length to the shaft of the unit unavoidably allows more movement. But of course, adding more height to the starlink unit can be advantageous too.

Easy to use with Starlink receiver. Very good fit. Well made

Perfectly mounted on the side of my house. You need a plastic adapter so it fits tight and doesn't damage the starlink but that can be 3D printed if you have one or bought on Amazon for 20 bucks.