SPACEKEEPER Workbench Casters kit 660 Lbs - Retractable Casters Heavy Duty Bench Caster Wheels Designed for Workbenches Machinery & Tables, 4 Pack

I constructed a heavy duty lathe workbench from Fir 4 x 4s and 2 x 4s plus two layers of 3/4” MDF for the top. I selected the Model 3000 Premium Workbench Casters primarily for their retractability, weight capacity of 660 lbs heavy duty construction and designed around 2.5” wide legs or greater. The Casters were easy to assemble but I would recommend assembling one first to understand the design. Included with the parts were two wrenches for tightening nuts & bolts however I also used a metric socket set as well. The Easy-Install Template is a snap to use and accurate. I used Frogtape to draw center lines and hold Template in place on the legs because the legs were finished. Since my 4 x 4 legs actually measured 3.5” sq. I was able to use the 4 corner holes. With Template in place I used a center punch to locate the holes precisely through the Template. The Wood Screws included with the Workbench Casters were a disappointment. The Phillips heads were easy to cam-out despite a new driver bit and clutch setting of the drill driver. I opted for a heavier #10 x 1.5” Drill Screw with 5/16” Hex Head and continued driving screws with nut driver bit. I found it much easier to attach the Leg Mounting Plate to the bench leg first, drive in the screws and then assemble the remaining caster parts because the 5/16”Hex Head required more space between the Pedal Bracket Assembly and Leg Mounting Plate. Your choice. The Movable Pedal of the Workbench Caster has a cam like bottom edge that exerts considerable force on the Wheel Mounting Plate when pushing down to elevate workbench. I noticed a metallic rubbing sound on one caster assembly. I applied a fine bead of white grease to the bottom edge of the Movable Pedal to lubricate that mating surface. The Model 3000 Premium Workbench Casters are well made, function exactly as designed and compliment my lathe bench. The completed workbench and lathe weigh in at 256 lbs well within the capacity of the casters. It’s possible for me to elevate the workbench and move it away from wall for cleaning.

These wheels worked prefect for the stage prop I built. Putting it on and off stage is easy and much better than using a dolly. Will definitely buy again. The instructions were perfect for getting the placement right.

Once installed, these SPACEKEEPER Workbench Casters work as expected and make it very easy to move around a shop table that I just finished out of scrap wood and tempered hardboard. Like so many “some assembly required” projects, it takes you forever to finish the first [only] set of casters. If you were to do an additional ten, it would take you the same amount of time as the first project, since you know the tricks to use, and the mistakes to avoid. Please note these are to be mounted to the sides of your bench legs and not underneath the bottoms of the legs, so plan your design accordingly. In the “down” (rolling around) position, you add only ¾” to your table height (see photos). So here are my complaints and recommendations if you buy this caster set: 1. The instructions are pretty much worthless. They basically say “put together and mount on table legs.” No helpful step by step details and the included drawings (on one little square of paper) don’t match the items in the kit. Mine was labeled “upgraded version” so maybe the drawings referred to the parts in the non-upgraded version. It was frustrating trying to follow the limited (three!) steps because you have to figure out the orientation of parts that don’t look like the ones in the drawing. 2. The kit is supposed to include 4 wrenches but instead there are two stamped metal pieces with various cutouts shaped like bolt heads and nuts. I tried using them and quickly switched to real tools – much easier. 3. The instructions indicate you should assemble the caster units entirely and then mount them with the provided screws. I did that, only to find that to mount the screws in the bottom part of the bracket, you have to take the caster unit apart again to gain access to the holes (see photo). Lesson learned: attach the step-down pedal (with the red tip) to the bracket and also assemble the caster stem in the lower part of the unit (“wheel mounting plate”), but don’t attach that to the black bracket yet. Instead, locate, pre-drill pilot holes, and screw the bracket to the leg first, then attach the caster stem and lower part of the unit to the bracket. Adjust tension on the bolt and nut that hold the step-down pedal until it takes a slight push to make it go down, but not so tight it won’t easily lift up again. 4. The template would be a good thing to use to help accurately place the bracket on your bench leg if only it was the right dimension – which it’s not. It is crucial to mount these things exactly right so your table sits flat/stable when the caster wheels are “up” and rolls freely when the caster wheels are down. The problem is that the template is 1/16” too short and 3/8” too narrow to match the footprint of the black brackets. So beware. I trimmed my template correctly with a razor knife to the right size. I also elected to mount the units inside the legs so as to avoid a stumbling hazard. You may want to do likewise (see photo). 5. The screws included are complete crap and should be discarded immediately. Don’t do as I did and have three of them cam out when pressure was applied (see photo). With a fourth one, the screw head snapped off completely, leaving about 2/3 of the screw shaft irretrievably buried in the wood. When I switched to my own supply of wafer head screws (see photo), I was able to mount the brackets without issue. Once installation was completed, I was able to dance the workbench around the shop with ease. Stepping down and toe-ing up the red-tipped pedals is a snap. All-in-all, I am very satisfied and for Chinese-made parts, these are not too bad. I have another table on which I used 360-degree casters with brakes, mounted underneath the bottoms of the legs, and they are a real pain to operate. These SPACEKEEPER Workbench Casters I would recommend if you are reasonably handy.

I purchased these retractable castors to add to a large workbench I was building for my garage. The casters didnt disappoint. They are extremely well made and cope very well with the weight of the bench. They lift the bench with ease and its a breeze to move it around the garage on the 3" wheels I cant recommend them highly enough and wouldnt hesitate to buy them again

I have these wheels under my workbench which is 200+kg. It so nice to be able to lift and move it on my own. The wheels were very easy to install and run smoothly. The only problem I have with them is that they stick out quite a lot, even when retracted. I often hit my toes against them when I walk around my bench. If there is space for the wheels (and your foot!) I recommend installing them on the inside of your bench.

He abierto el paquete y comprobado por encima y todo parece estar bien. No he querido sacar las ruedas y accesorios porque no las voy a instalar ahora, sino estas vacaciones de verano en que haré el banco de trabajo. Viene todo tan "encajado" en su sitio que si lo saco luego no voy a ser capaz de volver a colocarlo tan bien y la caja no cerrará. Bueno a lo importante: de la inspección somera puedo decir que se ve un material de buena calidad y completo. No creo que tenga problemas con el producto una vez instalado.

The product came with a template for installation which made things easy. The casters work great making my work bench easy to move. I Highly recommend this product.

Sono perfette, le uso per spostare un tavolo da lavoro su cui spesso carico pesi notevoli, e non subiscono nessuna deformazione.