HESAI 3D Printer Controller Kit for Arduino Mega 2560 R3 Board + RAMPS 1.4 Controller Control Panel + 5pcs A4988 Stepstick Stepper Motor Driver Module + Heat Sink
Thumbnail 1Thumbnail 2Thumbnail 3Thumbnail 4Thumbnail 5Thumbnail 6Thumbnail 7Thumbnail 8

HESAI 3D Printer Controller Kit for Arduino Mega 2560 R3 Board + RAMPS 1.4 Controller Control Panel + 5pcs A4988 Stepstick Stepper Motor Driver Module + Heat Sink

ID del producto: 54864903
Transacción segura
Comprados juntos con frecuencia

Descripción

  • Fully assembled & tested, no soldering required
  • Designed to fit the entire electronics needed for a RepRap in one small package for low cost.
  • Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.
  • A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

Note:The Color Of A4988 Will Be Shipped In Random(green or red)MEGA 2560 R3 BoardThe Mega is 100% compatible with Arduino and most shields designed for the ArduinoThe chip is Atmega2560-16au and Atmega16u2, same with the official version.Improved and expert version: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible both with the board that use the AVR, which operate with 5V and with the Due that operate with 3.3V. The second one is a not connected pin, that is reserved for future purposes.Stronger RESET circuit.It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.RAPMS 1.4 ControllerFully assembled & tested, no soldering requiredDesigned to fit the entire electronics needed for a RepRap in one small package for low cost.Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.Package List:1x MEGA 2560 R3 Board1x RAMPS 1.4 Controller5x A4988 Driver5x Heat Sink1x Screwdriver

Preguntas comunes

Trustpilot

Trustscore 4.5 | Más de 7,300 reseñas

Alí H.

Envío rápido y embalaje excelente. La herramienta Leatherman parece de primera calidad y resistente.

Hace 1 día

Yusuf A.

En general, fue una experiencia fantástica. Se lo recomendaré a mis amigos y familiares.

Hace 1 mes

Compre globalmente, ahorre con Desertcart
Valor por dinero
Precios competitivos en una amplia gama de productos.
Compre globalmente
Sirviendo a millones de compradores en más de 100 países
Protección mejorada
Opciones de pago confiables que adoran los compradores de todo el mundo
Garantía del cliente
Opciones de pago confiables amadas por los compradores de todo el mundo.
Aplicación DesertCart
Compre sobre la marcha, en cualquier momento y en cualquier lugar.

Actualmente agotado

Nicaraguaalmacenar

Lo sentimos, este artículo de nuestro Nicaragua La tienda está agotada. Estaremos reabasteciendo pronto: vuelva a consultar o comuníquese con el soporte técnico para productos similares.

Trustpilot

Trustscore 4.5 | Más de 7,300 reseñas

Fátima A.

El mejor envío internacional que he probado. ¡Vale cada centavo!

Hace 3 días

Reema J.

Plataforma perfecta para artículos difíciles de encontrar. La entrega fue rápida.

Hace 1 mes

Hesai 3d Printer Controller Kit For Arduino Mega 2560 R3 | Desertcart Nicaragua