Delid-Die-Mate - AMD Ryzen 7000 CPU Delid Tool - Processor Heatspreader Removing Tool - Delidding Tool Developed by der8auer - Enhances Cooling

The device works. It doesn't break the cpu.The only downside is that using liquid metal on these is dangerous. The hight is so low that any excess liquid metal will go on the resistors, so use nail polish or something to cover them. This was less of an issue with intel cpus.I don't plan on doing this to my 9900x. It did decrease the temps by 5c, but not worth it given the minimal gains. Intel used to get you 20c.I have a custom water loop and used this on a 7800x3d.

Got this in, still waiting on the TG AM5 heatspreader which should arrive tomorrow so I cannot speak to temps yet but...Device is very well machined and ready to delid right out of the box. I popped in my $700 CPU and noticed a few things different than my previous 14700K and 14900K delids. The ease of which the 9950X3D comes apart is amazing, the intel chips snapped apart. This was very drama free and it really just comes down to moving back and forth about 30 times (for me, some people have to do it 100's) until the red block just slid around on its own. It took about 8 minutes or so with hand cranking on the allen wrench, I did not use a drill. Once the red piece freely moved I knew the IHS and die's were separated fully. Pulled the unit apart and yep, this was delidded without cracks/breaks/drama. It did not snap apart, make any noise, this indium solder is very soft.I cleaned up the cpu with maybe 6 runs of rubbing in DC2 Pro liquid metal, then switched to flitz polishing compound until the dies were all mirror like. I did the same for the IHS but the indium was very thick on the IHS side. I eventually just used a small bamboo stick from another delid kit I had and just pushed off the solder then cleaned it up with the flitz.Right now the cpu is working, I am using it to type this review. I just have polar therm x10 on the die and on the IHS side until I get the heatspreader in. Temps basically the same but I did set the cpu to 65w eco mode just incase.This is definitely more clean up work than raptor lakes since you deal with 2 cores and the memory/io die but it is 100% compatible with ryzen 9000 and the X3d variants.

I just used this tool to delude an AMD Ryzen 8000. It worked perfectly with one pass through the sliding cycle. This tool is very precisely made and is a real value.

This thing totally worked as advertised. Very well designed and made from top quality materials. It took me about 30 "back & forth" movements until my IHS just "fell off". Using liquid metal I lowered my all-core temps (water cooled) by over than 20C. Using mild water chilling I can get a sustained 5.7Ghz+ all core overclock and still only hit 55-60C. That's a 400MHz overclock and the temps are only 15C over idle!!! Amazing product but not for the faint of heart...

Got this for my first de-lidding attempt and it worked like a charm. Takes a while to get the IHS to fully separate, but slow and steady wins the race. Very small movements back and forth, but I found doing it quickly helps as the friction builds up heat and helps to loosen the solder quicker; it will start to rub, bundle and then flake out the small edges before eventually fully separating.Would highly recommend. Very sturdy construction and won’t fail you.

This can take upwards of 40+ rotations on both sides, so dont be surprised when it doesnt just come apart after the first 20 rotations. Once both sides are clearly loose enough where you dont struggle twisting then it is ready to take apart and open the IHS. Be extremely careful when removing so you dont damage anything

Thrust bearings constantly were falling apart on me. These are a ball bearing design which is rather ridiculous given the small m5 size.I actually have professionally specified roller bearings in the past and will again in the future (as part of an engineering role)… and the use of semi caged ball bearings like this was a huge fail. Right out of the gate one of the cages was damaged or something, and the balls were falling out. I spent more time trying to chase these tiny little balls around my work space than I did using the tool.Next up, no lubrication was supplied nor recommended. This is pretty crazy as we have a steel thread applying quite a bit of tensile stress to the internal aluminum threads. The force isn’t that great ultimately, and most people won’t use it that much. But the threads and the thrust all really benefit from lubrication.Combine that with this delidding project ending with killing my 7900x, I would give it a firm no go. Wish more effort had gone into the solutions from thermal grizzly. I previously had good things to say about them as a company/their products, but this was a fail.I have successfully de lidded my last two CPUs, without issue. I would not recommend it for the ryzens- the performance gain even when everything was working, was rather minimal

This works incredibly, just as advertised & while was scared when it arrived since I've never delidded a processor before, it is very beginner friendly & i highly recommend it! Even if you have no experience with delidding & custom overclocking, this things works amazingly! GO FOR IT!